1. Assemble the embedded parts

1. Rotate the 4 nuts to about 6 cm of the 4 embedded steel bars

2. Pass the pre-embedded steel bars through the four holes of the positioning plate

3. Add spacer above the positioning plate

4. With the four corners of the pre-embedded steel bars facing outwards, use a wrench to tighten the screws

5. Add a positioning circle at the bottom about 10 cm from the upper part

6. Wrap the screw rod with tape to avoid burying the cement to block the screw opening

7. Use a tape measure to confirm that the diagonal distance of the embedded parts is consistent

2. Digging and burying embedded parts

1. Outline the size of the embedded parts before digging the pit, and the foundation pit should be horizontal, flat and straight

2. The distance from the flange to the pit edge is not less than 20 cm Note: If the soil is soft, increase the size of the foundation pit

3. The depth of the embedded parts is more than 10 cm higher than the height of the embedded screw, and the depth of the buried box is more than 10-15 cm below the ground

4. The concrete is blended according to the international ratio. The blended concrete is poured into the dug pit to make a bottom. Stir with a shovel to ensure that the concrete is evenly poured. Place the embedded parts in the center of the pit and then bury them.

5. Constantly confirm the center position of the embedded parts during the burying process

6. Separate the embedded parts and the battery box area with bricks or boards

7. Confirm that the height of the battery box and the ground is not less than 10-15 cm

8. In order to facilitate maintenance, the battery box should be buried with loose soil as much as possible.

3. Battery connection, the battery is loaded into the battery box

1. Connect the positive and negative poles of the battery to ensure that the screws of the connecting wires are fastened

2. The sealing strip of the battery box plays a waterproof role, please do not forget to install

3. Align the holes of the sealing strip with the holes of the battery box

4. Cover the battery box with a sealing strip in the middle

5. The upper and lower covers of the battery box are fastened with screws to ensure tightness

6. Bury the embedded parts to expose the screw outlet and battery connection line

7. Flatten the surrounding area above the embedded parts

4. Assemble the light source and support arm

1. Pass the light source cable through the light pole support arm

2. Connect the lamp head to the support arm, and tighten the screws to fix it

3. After the lamp head and the arm are fixed, assemble the lamp head

4. After the lamp head is assembled, check to ensure that there is no gap in the middle

5. Use iron wire as a lead wire to pass from the hole of the pole arm to the bottom of the pole

6. Bundle the connector of the light source cable with the iron wire

7. Pass the light source connection wire through the light pole by pulling the lead wire

8. The hole of the arm is aligned with the hole of the light pole. Make sure that the arm and the light pole are on the same line. Tighten the screws to ensure that the arm is firmly fixed on the light pole.

5. Assemble the battery board and bracket

1. Pass the battery board cable through the battery board bracket

2. Align the holes of the pool plate with the holes of the battery plate bracket

3. Fasten the battery board and the battery board bracket with screws

4. First use a long enough wire to pass from the top of the light pole to the bottom of the light pole as the lead wire of the battery board connection line

5. After the lead is passed to the bottom, wrap the lead around the connecting wire of the battery board

6. Pull the lead from the bottom of the light pole and thread the connecting wire through the light pole

7. Put the diameter of the battery board bracket into the top of the light pole

8. Ensure that the bottom of the battery board bracket is level with the ground and tighten the screws

9. Check the coordination between the part of the battery board, the part of the arm and the light pole

Six, erect solar street lights

1. After the concrete of the embedded parts is firm and stable, safely erect the light pole to ensure that the flange holes are aligned with the holes of the embedded parts

2. Add gaskets above the flange and tighten the screws to ensure that the light pole is erected stably

7. Connect the controller terminals

1. Connect the plug on the controller to the plug in the light pole correspondingly

2. Unplug the insulating cap of the battery connection cable and connect it accordingly

3. After connecting the line, fix the controller in the light pole

4. Install the door of the light pole and fasten it with screws